1These instructions are to be left with the userInstallation and User GuideSHOWER VALVEMIRA DISCOVERY
10Flow Regulator RecommendedFlow Regulator RecommendedUnvented mains pressure systemThe shower can be installed with aunvented, stored hot water cyli
11INSTALLATIONGeneralInstallation must be carried out in accordance with these instructions, and must beconducted by designated, qualified and compete
12Installation MethodsExposed Discovery Shower ControlThe Exposed Discovery Shower Controlcan be installed with Rear, Rising or FallingSupply Inlets.F
13Exposed Shower Control1. Rear SuppliesTemplateWall PlugsSecuringScrewsShower ControlBackplateConcealing PlateApply Silicone Sealant153 mm10 mm depth
14Compression NutOliveSecure the Controlto the Backplate withthe GrubscrewElbow ShroudsCaution! It is essential at this pointthat the supply pipework
15TemplateWall plugsCold SupplyHot Supply2. Rising or Falling Supplies2.1 Remove the Elbow Shrouds from theShower Control.2.2 Rising Supplies: Loosen
16Securing ScrewsBackplateConnector coverCompressionNutOliveElbow ShroudSecure the Controlto the Backplatewith the Grubscrew‘O’ Seal2.7 Attach the Bac
17Built-in Shower Control1. Solid Wall or Stud Partition(Using Securing Brackets - Mounting off Front Face)1.1 Determine the route for the hot andcold
181.7 Fit the Securing Brackets to theShower Control.Important! Make sure that the correctholes are used, otherwise theBackplate cannot be fitted.Note
191.14 Attach the Building-in Shroud to theShower Control using the two SecuringScrews.1.15 Using the ‘Finished Wall Indicator’ onthe Building-in Shro
2CONTENTSIntroduction ... 3Safety : Warnings ...
202.1 Refer to section: ‘1. Solid Wall orStud Partition (Using SecuringBrackets - Mounting off Front Face)’and follow steps 1.1 to 1.4.2.2 Cut away th
21Hot SupplyCold SupplySecuringScrewRear FixingPointOutlet Pipe toFittings2.3 Mark the positions of the Fixing Screwholes on the wall.2.4 For solid wa
223. Laminated Panels(Using Securing Brackets - Mounting off Rear Face)Note! For laminated panels the showercontrol must be positioned from the rear o
233.8 Fit the hot and cold supply pipes andtighten the compression nuts.Caution! Make sure that the olives arefitted and all pipework is flushed throu
24Control AssemblyImportant! The Yellow Lugs on the FlowControl must be in the fully clockwise (off)position in order to fit the Control Assembly.Not
25REVERSED SUPPLIESThe Discovery Shower Control is supplied with inlet connections Hot-Left, Cold-Rightand Bottom-Outlet as standard. If the hot and c
2611. Rotate the Cartridge 180° to reverse the inlets to the Cartridge.Caution! Make sure the two Cartridge Side Seals are not damaged.12. Refit the C
27The Temperature Control Knobmust be in this position(the full cold position) over theGreen Temperature HubRotate the GreenTemperature Hub,fully cloc
28OFFTurn the Temperature Control KnobClockwiseto decrease the Temperature,Anticlockwiseto the Preset Maximum TemperatureTurn the Flow LeverAnticlockw
29FAULT FINDINGSYMPTOM1. Only hot orcold waterfrom theshower head.2. Fluctuating orreduced flowrate.3. No flow fromthe controloutlet.4. Blendtemperatu
3INTRODUCTIONThe Discovery Thermostatic Shower Control with independent selection for temperatureand spray force.Mira Discovery Exposed: Shower contro
30MAINTENANCEGeneralThe Mira Discovery Shower Control is designed to be maintenance free, as suchthere are no serviceable parts in the cartridge. Howe
31Flow diagramIn-service Test ProcedureNote! All measurements and results should be recorded in the Log Book.StartMeasure and record supply temperatur
32Filters - Exposed ModelsTo clean or replace the inlet filters:1. Isolate the hot and cold water supplies.2. Operate the Flow Lever to drain anyresid
33Filters - Built-in ModelsTo clean or replace the inlet filters:Note! Refer to the section ‘Installation, ControlAssembly’ for illustrations.1. Isola
34Valves operating outside these conditions cannot be guaranteed to operate asType 2 valves.ApplicationThe approved designations for Type 2 valves are
35NOTES
36NOTES
38SPARE PARTSExposed Thermostatic Shower Control090 95 Pipe Concealing Plates1595 036 Temperature Hub Assembly1595 037 Handle Pack1595 038 Handle Adap
39Built-in Thermostatic Shower Control1595 036 Temperature Hub Assembly1595 037 Handle Pack1595 038 Handle Adapter Pack1595 039 Cartridge Assembly Pac
4 1 x Shower Control 2 x Concealing Plates 2 x 15 mmCompression Nuts 2 x 15 mm Olives 1 x 2.5 mm Hexagon Key9 1 x O-Key 2 x Concealing Caps 2
40UKASP4924_5 © Kohler Mira Limited, May 2006CUSTOMER SERVICE
5Built-in Discovery Shower Control 1 x Control Assembly 3 x 15 mmCompression Nuts 3 x 15 mm Olives 1 x 2.5 mm Hexagon Key 1 x O-Key 2 x Wall Plu
6DIMENSIONSBuilt-in Discovery Shower Control15310613135706767 - 8530Ø183Ø56Exposed Discovery Shower ControlDimensions in mmBuilding-in Depth
7SPECIFICATIONSOperating ParametersFor Type 2 valves, the supply conditions specified in section: 'Type 2 Valves -Application' take precede
8Flow RatesTypical Flow Rates on Low Pressure Systems - Mira Discovery with Adjustable Fittingsor Rigid Head:Typical Flow Rates on High Pressure Syste
9Flow Regulator RecommendedINSTALLATION REQUIREMENTSIsolating valveMixing ValveTwin Impeller PumpTempering ValvePressure Reducing ValveSingle Impeller
Commentaires sur ces manuels